What Is 3D Puff Embroidery?
In the digital era, 3D Puff Embroidery Digitizing is done through embroidery machines and computer software. It is a digitizer that puts extreme effort to create appealing designs. This Embroidery Digitizing For Hats is different from simple designs, and there is depth in the artwork. However, you can do it by hand too. The effort is worthwhile, but it totally depends on you.
Over the last few years, there has been an increasing demand for 3D designs, especially with hats. So in this blog, we will discuss some tips on 3D hat embroidery to perform better and get the best result.
9 Amazing Tips For 3D Puff Embroidery Digitizing
- Set Your Machine Speed Wisely
Determining the perfect speed for your Stich Embroidery Machine is critical because it impacts the performance of embroidery designs. According to your orders, you will frequently need to slow down the speed. The maximum speed is distinct for each embroidery machine. A great way is to conduct a few experiments for different speeds and determine the best speed that can deliver the best results.
- Your Fabric Matters A Lot
Consider using slippery 3D puff fabrics. It is for two reasons. First, the density of the 3D puff embroidery stitch is higher as compared to normal designs. Secondly, when working with the rubber, the surface is too sensitive to vibrations in the hoops.
Therefore, thick, stable fabrics, like in caps, are preferred. With 3D puff embroidery, noble fabrics like those in towels also don’t go well. Therefore, their own loft fades the 3D effect and fails to cater to appealing designs.
- Use The Right Needle Thickness
We recommend using the sharp needle in 3D Puff digitizing that can quickly pierce through the foam.
- Choosing Your Foam
The selection of foam mainly depends on the model height for your Custom Embroidery. The thicker the foam, the higher the model height will be. However, dense foams are difficult to work with, although they create flashy designs. The thicker a foam is, the more it interferes with the smooth operation of the machine. Therefore, you should never select thick foams.
- Creating Stops & Laying The Foam
Once the flat design is done, you can create a stop. You need to learn how to create stops in your machine as this is something that you will need much in your career as you deal with 3D Embroidery Digitizing. You need to ensure that the machine provides enough stops on color changes.
Stick the foam either with a sticking spray or tape on top of the material. This is intended to keep the fabric in position and resist movement underneath.
- Making The Outline
Once you laid the foam and created a stop, you need to make a design outline before embroidering with satin stitches. This is because the outline will stabilize the field that can be broken down.
The setup increasingly becomes unstable due to the foam. And this is why the foam is stuck to the material. Stitching a design counteracts this volatility by presenting foam with the split.
- Remove The Excess Foam
After completing the template, remove the excess foam. Apply a heat source in case there are small pieces of puff that are so hard to remove with your hands.
You can use the heat gun to remove the foam. Some puff bits might remain stuck. Therefore, remove them with tweezers.
- Do Some Test Runs
Whenever you are dealing with a new design, try doing some test runs to avoid any mishaps. Compare with different models and select the fabric and equipment that works great.
This drill helps novice embroiders evaluate what is working and what is not working well. It also allows them to take advantage of the best situations for real sew-out and similar future work.
- Level Up Your Switch Density
In 3D puff embroidery digitizing, stitch density is kept higher as compared to normal flat designs. When we speak of high density, we basically refer to the satin stitches on top of the design.
There should be a natural thickness underneath the stitches. Most computerized machines are able to manage various stitches densities that allow you to close and tight underlaid stitches.
A higher density of top satin stitches than underneath stitches allows a popped 3D-ish effect for the embroidery design.
A Simple Hack of 3D Puff Embroidery Digitizing For Hats
Now, we will share with you a simple hack of 3D Puff Embroidery Digitizing For Hats. Many times you will notice that when the 3D foam part is ready, digitizers take and hold it with their hands to maneuver it when it is sewn.
However, there is a good way to do this. When you hoop the hat, take a rubber band and then put it on the cap. You don’t need a custom rubber band. A simple rubber will do the same.
When your design is ready for the puff, take the puff and put it in place. Take a portion of the rubber band and then put it on the top. Now, you are fine to go with the sewing process. You can remove the excess foam once your design is done.
So, this is the overall process and hack of 3D Puff Embroidery Digitizing For Hats.
If you have any complications, avail the best 3D Digitizing Services of Climax Digitizing.
